A&D AD-4212A/B Manuale Utente Pagina 39
- Pagina / 102
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
37
DP (Dump print) format 5if type 1
This format is used when the peripheral equipment can not receive the A&D format.
If an AD-8121B is used, set the printer to MODE 3.
This format consists of sixteen characters excluding the terminator.
A header of two characters indicates the balance condition. No overload header is used.
The polarity sign is placed before the data, with spaces in place of leading zeros, if the data is
not zero or overloaded.
The unit, consisting of three characters, follows the data.
KF format 5if type 2
This is the Karl-Fischer moisture meter format and is used when the peripheral equipment can only
communicate using this format.
This format consists of fourteen characters excluding the terminator.
This format has no header characters.
The polarity sign is placed before the data, with spaces in place of leading zeros, if the data is
not zero or overloaded.
This format outputs the unit only for a stable value.
MT format 5if type 3
A header of two characters indicates the balance condition.
The polarity sign is used only for negative data.
The weighing data uses spaces in place of the leading zeros.
The character length of this format changes dependent upon the unit
NU (numerical) format 5if type 4
This format outputs only numerical data.
This format consists of nine characters for the AD-4212A series balance or ten characters for
the AD-4212B series balance, excluding the terminator.
The polarity sign is placed before the data with the leading zeros. If the data is zero, the plus
sign is used.
(AD-4212A series balance)
(AD-4212B series balance)
W T + 0 . 1 2 7 8 g
C
R
L
F
T
WT
US
QT
Stable header Stable header of counting mode
Unstable header
Header Data Unit Terminator
Stable value
Unstable value
Data Unit Terminator
S 0.1278 g
C
R
L
F
S
SD
SI
Stable header
Unstable header
Overload header
Header Data Unit Terminator
Data Terminator
+ 0000.1278
C
R
L
F
+
+ 000.1278
C
R
L
F
+
Data Terminator
- AD-4212A/B 1
- CONTENTS 3
- 1. INTRODUCTION 6
- 1-2 Compliance 7
- 2. UNPACKING THE BALANCE 8
- Accessories 9
- 2-2 Installing the Balance 10
- Slide the connector sleeve 11
- Unlocked 11
- 3. PRECAUTIONS 12
- Metal case 13
- Grounding 13
- Influence of the air flow 14
- 3-4 After Use 15
- 3-5 Power Supply 15
- 3-3 During Use 15
- Key operation 16
- Display symbols 16
- 5. WEIGHING UNITS 17
- 5-2 Changing the Unit 19
- 6. WEIGHING 20
- 6-2 Smart Range Function 21
- Operation 22
- 8. CALIBRATION 23
- 8-1 Calibration 24
- From previous page 25
- Calibration 25
- GLP output 25
- 8-2 Calibration Test 26
- 9-1 Permit or Inhibit 28
- With these keys 29
- Press the key 29
- 10. FUNCTION TABLE 30
- Caution 34
- Cond ) 35
- prt 0 Key mode 37
- + 0000.1278 39
- + 000.1278 39
- 2004/07/01 40
- 10-8 Data Format Examples 41
- 10-10 Comparator Function 44
- 11-1 Setting the ID Number 48
- 11-2 GLP Report 49
- 12. COUNTING MODE (PC) 52
- Place sample 53
- The counting result 53
- 13. PERCENT MODE (Pct) 54
- 14. DATA MEMORY 55
- Storing the weighing data 56
- Setting the function table 57
- Recalling the memory data 57
- Transmitting the memory data 59
- Deleting the memory data 59
- Recalling the unit mass 60
- Upper/lower limit value code 62
- (AD-4212A only) 64
- (Standard interface) 65
- Use a shielded 66
- 18. COMMANDS 70
- 19. BCD OUTPUT (OP-01) 73
- Balance interior 74
- Output signal GND 74
- 21. MAINTENANCE 79
- 22. TROUBLESHOOTING 79
- 22-2 Error Codes 81
- 22-3 Asking For Repair 83
- 23. SPECIFICATIONS 84
- Minimum 100% 85
- AD-4212A-100/200 86
- AD-4212B-201/301 86
- AD-4212B-101/102 86
- Using the pan boss 87
- Installing in a panel 92
- Attachment Procedure 93
- AD-4212A-600/1000 95
- * Adjustable range 95
- 28. OPTIONS 96
- 29. TERMS/INDEX 98
Prodotti e manuali riguardandi Misurazione, test & controllo A&D AD-4212A/B
(144 pagine)
(4 pagine)
(42 pagine)Slant_fin SC-3 manuali
Manuali dei proprietari e guide per l'utente per Apparecchiature Slant_fin SC-3.
We fornisce 1 manuali pdf Slant_fin SC-3 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale