A&D AD-4212A/B Manuale Utente Pagina 61
- Pagina / 102
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
59
14-5 Memory for Upper/lower limit values
Upper/lower limit values stored in memory can be selected easily by pressing the MODE key.
Storage capacity for the 3-level comparison is 20 sets of upper/lower limit values (code
numbers C01-C20). "C01" is to store the upper and lower limit values that are set in the function
table.
The code number appears in the upper left of the display to label the value.
Using commands, the upper/lower limit values can be recalled and changed.
Notes
If the data memory function is used, the “Title block” and “End block” can not be output.
This function is not available when the BCD output (OP-01) is installed.
Setting the function table
1 Set the “Data memory ( data )” parameter to “4”.
Note
If “Clr” appears blinking in the upper left of the display, delete the data in memory.
- AD-4212A/B 1
- CONTENTS 3
- 1. INTRODUCTION 6
- 1-2 Compliance 7
- 2. UNPACKING THE BALANCE 8
- Accessories 9
- 2-2 Installing the Balance 10
- Slide the connector sleeve 11
- Unlocked 11
- 3. PRECAUTIONS 12
- Metal case 13
- Grounding 13
- Influence of the air flow 14
- 3-4 After Use 15
- 3-5 Power Supply 15
- 3-3 During Use 15
- Key operation 16
- Display symbols 16
- 5. WEIGHING UNITS 17
- 5-2 Changing the Unit 19
- 6. WEIGHING 20
- 6-2 Smart Range Function 21
- Operation 22
- 8. CALIBRATION 23
- 8-1 Calibration 24
- From previous page 25
- Calibration 25
- GLP output 25
- 8-2 Calibration Test 26
- 9-1 Permit or Inhibit 28
- With these keys 29
- Press the key 29
- 10. FUNCTION TABLE 30
- Caution 34
- Cond ) 35
- prt 0 Key mode 37
- + 0000.1278 39
- + 000.1278 39
- 2004/07/01 40
- 10-8 Data Format Examples 41
- 10-10 Comparator Function 44
- 11-1 Setting the ID Number 48
- 11-2 GLP Report 49
- 12. COUNTING MODE (PC) 52
- Place sample 53
- The counting result 53
- 13. PERCENT MODE (Pct) 54
- 14. DATA MEMORY 55
- Storing the weighing data 56
- Setting the function table 57
- Recalling the memory data 57
- Transmitting the memory data 59
- Deleting the memory data 59
- Recalling the unit mass 60
- Upper/lower limit value code 62
- (AD-4212A only) 64
- (Standard interface) 65
- Use a shielded 66
- 18. COMMANDS 70
- 19. BCD OUTPUT (OP-01) 73
- Balance interior 74
- Output signal GND 74
- 21. MAINTENANCE 79
- 22. TROUBLESHOOTING 79
- 22-2 Error Codes 81
- 22-3 Asking For Repair 83
- 23. SPECIFICATIONS 84
- Minimum 100% 85
- AD-4212A-100/200 86
- AD-4212B-201/301 86
- AD-4212B-101/102 86
- Using the pan boss 87
- Installing in a panel 92
- Attachment Procedure 93
- AD-4212A-600/1000 95
- * Adjustable range 95
- 28. OPTIONS 96
- 29. TERMS/INDEX 98
Prodotti e manuali riguardandi Misurazione, test & controllo A&D AD-4212A/B
(144 pagine)
(4 pagine)
(42 pagine)Slant_fin SC-3 manuali
Manuali dei proprietari e guide per l'utente per Apparecchiature Slant_fin SC-3.
We fornisce 1 manuali pdf Slant_fin SC-3 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale